How To Change Roomba Home Base Location

1. Find a level spot for your home base that is at least three feet by three feet.
2. Make sure the charging dock’s signal is unobstructed and that there is nothing blocking the path between your home base and the charging dock.
3. To dock Roomba on the home base, line up the Home Base’s charging contacts with the charging contacts on the bottom of Roomba.
4. Gently press down on Roomba until it clicks into place on the Home Base. The Home Base is now ready to charge Roomba.

How to Set Up the Home Base | Roomba® | iRobot®

Moving the Charging Base / Dock – Roborock S4

How do I change my Roomba’s home base location?

If your Roomba is not cleaning in the areas that you want it to, you may need to change the location of its home base. To do this, first make sure that your Roomba is powered off. Then, find the two blue arrows on the top of the home base. Press and hold down both arrows simultaneously for three seconds. The lights on the home base will flash, indicating that the home base is ready to be moved. Pick up the home base and place it in the desired location.

Can I move my Roomba’s home base to another location?

As long as your new home base is within range of the original home base, you can absolutely move your Roomba’s home base to another location!

How do I keep my Roomba from going to its home base?

There are a few things you can do to keep your Roomba from going to its home base. One is to make sure that the home base is not in a high traffic area where the Roomba will be constantly bumping into things and getting stuck. Another is to ensure that the home base is not in a spot where there is a lot of dust or debris. Finally, you can try placing a piece of tape over the home base sensor to trick the Roomba into thinking it is not there.

How do I clean my Roomba’s home base?

Assuming you are referring to the home base that comes with the iRobot Roomba:

To clean the home base, start by unplugging the unit. Then, use a dry or slightly damp cloth to wipe down the charging pins. You can also use a cotton swab to clean out the dirt and debris from the crevices. If the home base is very dirty, you can clean it with a mild soap and water solution. Just be sure to dry it thoroughly before using it again.

Why does my Roomba go to its home base?

If your Roomba is going to its home base, it is likely because it is either out of battery or it is full. Once your Roomba’s battery is depleted, it will automatically return to its home base to recharge. If your Roomba is full, it will also return to its home base so that you can empty it out.

How do I make my Roomba go to its home base?

If you need to make your Roomba return to its home base, there are a few things you can do. First, make sure that the home base is powered on and in range of the Roomba. Then, press the clean button and the home button at the same time. The Roomba should start beeping and then drive to the home base.

How can I stop my Roomba from going to its home base?

There are a few things you can do to stop your Roomba from going to its home base. One is to simply pick it up and move it to where you want it to go. Another is to block the path to the home base with something like a chair or a box. You can also remove the home base entirely.

What happens if I move my Roomba’s home base?

If you move the home base, your Roomba will not be able to find its way back to the charging dock. It is important to keep the home base in the same place so that your Roomba can charge itself and be ready for the next cleaning cycle.

I don’t want my Roomba to have a home base. How do I disable it?

There are a few reasons you might not want your Roomba to have a home base. Maybe you’re worried about it getting stuck under furniture or you’re worried about it running into something and breaking. If you have your Roomba set to clean a specific room or area, you can disable the home base feature by following these steps:

1. Press the clean button on your Roomba.

2. Press the dock button. The LED will blink red and then turn off, indicating that the home base feature has been disabled.

3. You can now move your Roomba around without it automatically returning to its home base. Remember to press the clean button again when you’re finished so that it doesn’t continue cleaning on its own.

How do I change my Roomba’s home base settings?

If you want to change your Roomba’s home base settings, first make sure that it is turned off. Then, press and hold the “clean” and “spot” buttons simultaneously for three seconds. This will put the Roomba into its setting mode. Use the arrow buttons to navigate to the “home base” option, and then press the “clean” button to select it. From there, you can use the arrow buttons to change the home base settings as desired. Once you’re finished, press the “clean” button again to save your changes and exit the setting mode.